What is the most important part of a flooring job?

The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.

Should I replace my old hardwood or refinish it?

If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.

Can I put hardwood on a concrete slab?

Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.

Which floor holds up best in Georgia humidity?

Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.

How long does new flooring take?

A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Flooring Installation in Sandy Springs, GA

Thinking about one continuous floor across your Sandy Springs split-level? It can be done, but the main level sits on framing, the lower level on a slab, and stair nosings sized for carpet won't fit a thicker floor without planning. Many 60s ranches in Riverside and Mount Vernon Woods also have oak strip under the carpet worth refinishing, and walkout slabs get a moisture test. Start with the details below.

Get a free estimate (470) 419-0922

Fulton County · Sandy Springs, GA

Flooring Installation for Sandy Springs homes

The core stock is postwar. Mount Vernon Woods has late-50s ranches and early-60s split-levels next to colonials and newer builds, Riverside is mostly ranches and traditional two-stories from the 60s and 70s on winding, hilly streets, and Huntcliff, set in a bend of the Chattahoochee around the Cherokee Country Club golf course, filled in through the late 60s and 70s on steep, wooded lots, many of them on septic. The terrain is the thread that ties it together. Sloped lots put a daylight or walkout basement under a lot of these houses, push decks up off the main floor, and keep siding and trim in shade and leaf litter for most of the year. Inside, the split-level and the walled-off ranch kitchen are the layouts owners most want to change. Around City Springs and Perimeter Center the picture shifts to apartments, condos and office towers, which is where the commercial repaint work sits.

Areas we work in Sandy Springs

Riverside
Mount Vernon Woods
Huntcliff
North Springs
The Panhandle
Chastain Park

Near City Springs and Heritage Green, Heritage Sandy Springs Museum, Morgan Falls Overlook Park and across the rest of Sandy Springs.

Open living area with dark refinished hardwood, gray walls and a stair rail — Photos from recent WS Painting & Remodeling jobs across the metro.

Open living area with glossy oak floors, white walls and white square columns — Photos from recent WS Painting & Remodeling jobs across the metro.

Flooring Installation on Sandy Springs houses

Flooring jobs in Sandy Springs often start with finding out what is under the carpet. Many 60s ranches in Riverside and Mount Vernon Woods have original oak strip flooring that can be refinished or matched instead of replaced. Split-levels add a different challenge: each level and stair run needs a transition, and owners often want one continuous floor across levels that were built with different materials. Walkout basements need flooring rated for concrete and occasional moisture. In larger homes along the river, long open runs make it important to plan board direction and expansion space carefully.

What usually gets missed

On a split-level, the trap is running one continuous floor without working out the heights first. The main level sits on wood framing, the lower level on a slab, and the stair nosings were sized for the original carpet, so a thicker new floor leaves the top step short and the bottom step tall. Walkout slabs on the uphill side can also give off moisture that looks dry to the eye. We measure every stair rise and test the lower slab before a product is chosen.

On a Sandy Springs job we check

Pull up a corner of carpet to look for original oak strip
Measure each split-level stair rise before picking a thicker floor
Test the walkout slab for moisture before choosing a product

5.0 from 44 Google reviews. A supervisor runs every job on site.

(470) 419-0922

What the job actually involves

A floor is only as good as what it sits on. Most of a flooring job is the part you never see — checking the subfloor for flatness, moisture and movement, and fixing it — because that is what decides whether the finished floor stays flat, quiet and tight instead of cupping, gapping or squeaking in a year or two.

We install laminate, luxury vinyl plank, engineered and solid hardwood, and tile, matched to the room: vinyl or tile over slabs, basements and wet areas, hardwood in conditioned living space, with the underlayment and transitions the material calls for. We do not pair a good floor with the thinnest underlayment to shave the quote, because that is where noise and early wear come from.

How we run a flooring installation job in Sandy Springs

1

Pull back a corner and see what is really there

Before anything is ordered we lift a corner of the existing carpet or flooring to see the subfloor, the height against the next room, and whether the house is on a slab or a crawlspace. What is under the floor, not the sample in the showroom, decides what can go down and what prep it needs.
2

Test for moisture and check the subfloor

Slabs and crawlspace subfloors are checked for moisture before any wood or vinyl is committed, because flooring laid over a wet base fails no matter how well it is installed. We also check the subfloor for flatness and for loose, soft or squeaking spots, and note the height difference into every adjoining room.
3

Fix and flatten the subfloor

High and low spots are ground down or filled with leveling compound, loose panels are refastened to the joists, and soft or water-damaged decking is cut out and replaced. On a crawlspace house a ground vapor barrier is part of keeping the new floor dry. This step is skipped on cheap jobs and is the reason they fail.
4

Acclimate the material

Wood and some vinyl are brought into the actual rooms and left to reach the home humidity before a board goes down. In a Georgia summer that matters: material installed straight off the truck swells or shrinks to the room later and opens gaps or buckles. We measure it rather than guess.
5

Lay the floor and handle transitions

The floor goes down by the method the material calls for — nail, glue, or floating click — with the right underlayment under it. Thresholds and transitions into tile, other rooms and stair nosings are cut so there is no trip edge, and doors are undercut so they still swing.
6

Trim, clean and walk it

Shoe molding or base is set to cover the expansion gap, seams and transitions are checked, and the floor is cleaned. We walk it with you in good light, looking for lifted edges, hollow spots and anything that catches, and work a punch list before it is closed out.

What moves the price

We will not quote Sandy Springs blind over the phone — these are the things we look at on site that decide the number.

What is under the existing floor. Carpet over sound plywood pulls up easily; tile or glued vinyl, or a bad subfloor found underneath, adds removal and prep that a showroom quote never includes.
Material class. Laminate and vinyl plank sit at the low end, engineered hardwood and tile in the middle, and solid site-finished hardwood or natural stone at the top.
Subfloor repair and leveling. Grinding high spots, filling low ones, replacing soft decking, or adding a crawlspace vapor barrier is priced once the old floor is up.
Slab versus crawlspace. A slab limits solid hardwood and may need moisture control; a crawlspace can need subfloor and vapor work before new flooring goes down.
Square footage, and how cut-up the space is. Closets, angles, stairs and lots of doorways slow a job and add transitions and waste.
Stairs, patterns and transitions. Stair treads, diagonal or herringbone tile, and tying several finishes together at thresholds all add labor over a plain straight-lay field.

See typical flooring installation price ranges →

From a flooring installation customer

“They knocked down and built a complete new wrap around deck and installed cable for the railings. … Repaired and replaced siding and flooring due to extensive rot. … Dan provided daily updates and pictures of the project.”

Diana Lutian
Cabin deck, siding, bath and flooring
July 2025

All 44 reviews →

Want a real number for your Sandy Springs flooring installation job?

The only way to price it honestly is to see it. We come out, walk the job and put it in writing — free, and with no obligation to book.

Call and we answer 24/7. Forms sent during the day get a call back the same day.

Call (470) 419-0922 Get a free estimate

Flooring Installation in Sandy Springs — questions we get asked

What is the most important part of a flooring job?: The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.
Should I replace my old hardwood or refinish it?: If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.
Can I put hardwood on a concrete slab?: Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.
Which floor holds up best in Georgia humidity?: Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.
How long does new flooring take?: A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Planning flooring installation? Start here

Everything about flooring installation →

More in Sandy Springs

Fulton County housing, neighborhoods and what we do there.

Painting & remodeling in Sandy Springs →

Other work in Sandy Springs

Flooring Installation nearby

Prefer to talk it through? Dan picks up.