What is the most important part of a flooring job?

The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.

Should I replace my old hardwood or refinish it?

If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.

Can I put hardwood on a concrete slab?

Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.

Which floor holds up best in Georgia humidity?

Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.

How long does new flooring take?

A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Flooring Installation in Roswell, GA

If your Roswell home still has carpet, parquet and sheet vinyl side by side, you are in good company in Martin's Landing and Horseshoe Bend. Most owners want one continuous main-level floor, and that starts with a subfloor checked for dips and screwed down where it squeaks. Old vinyl and mastic get tested before removal, and walk-out basement slabs need a below-grade product. Describe your rooms to start an estimate.

Get a free estimate (470) 419-0922

Fulton County · Roswell, GA

Flooring Installation for Roswell homes

Roswell's population multiplied between 1970 and 2000, and the housing records that growth. Martin's Landing and Brookfield Country Club date mostly to the late 1970s; Horseshoe Bend, Saddle Creek, Loch Highland and Wildwood Springs filled in through the 1980s; Barrington Farms and Edenwilde followed in the 1990s. Much of that stock is wood-sided or wood-trimmed, with cedar, hardboard and brick fronts, and the rolling ground that falls toward the river and the creeks gives many lots a slope and a walk-out basement. Older still is the historic district: the Mill Village around Sloan Street, where some millworker housing dates to the 1850s, and the blocks along Canton Street and Mimosa Boulevard, with old wood, plaster and many layers of earlier paint. Newer infill townhomes, such as Harlow and Ashbury, are the exception rather than the rule. For painting and remodeling that adds up to a lot of carpentry before paint, decks and siding at replacement age, and kitchens and baths on their first or second remodel.

Areas we work in Roswell

Martin's Landing
Horseshoe Bend
Brookfield Country Club
Barrington Farms
Saddle Creek
Mill Village

Near Bulloch Hall, Barrington Hall, Roswell Mill ruins and the Vickery Creek trails and across the rest of Roswell.

Kitchen with cherry cabinets, a granite island and dark hardwood floors under recessed lights — Photos from recent WS Painting & Remodeling jobs across the metro.

Corridor with blue-gray wainscot paint, white upper walls and new light oak flooring — Photos from recent WS Painting & Remodeling jobs across the metro.

Flooring Installation on Roswell houses

Roswell homes from the 70s and 80s often still have a patchwork of floors: wall-to-wall carpet, parquet or strip oak in the foyer, and sheet vinyl in the kitchen and baths. Owners in Martin's Landing, Horseshoe Bend and Highland Colony usually want one continuous floor across the main level, either hardwood or a good engineered or luxury vinyl plank. Those houses typically have a framed floor over a basement or crawlspace, and after decades the subfloor can squeak and dip between joists. Walk-out basements on sloping lots bring a concrete slab that needs a product rated for below grade.

What usually gets missed

The usual mistake is laying new flooring over an uneven or squeaky subfloor. A long plank floor shows every dip, and click-together products break at the joints when the floor flexes. We check the main level for flatness and screw down loose sheathing before installing. Old vinyl and adhesive are tested before removal, and basement slabs get a moisture test before any product is chosen.

On a Roswell job we check

Check the main-level subfloor for dips and squeaks
Test old vinyl and mastic before tearing it out
Run a moisture test on the basement slab first

5.0 from 44 Google reviews. A supervisor runs every job on site.

(470) 419-0922

What the job actually involves

A floor is only as good as what it sits on. Most of a flooring job is the part you never see — checking the subfloor for flatness, moisture and movement, and fixing it — because that is what decides whether the finished floor stays flat, quiet and tight instead of cupping, gapping or squeaking in a year or two.

We install laminate, luxury vinyl plank, engineered and solid hardwood, and tile, matched to the room: vinyl or tile over slabs, basements and wet areas, hardwood in conditioned living space, with the underlayment and transitions the material calls for. We do not pair a good floor with the thinnest underlayment to shave the quote, because that is where noise and early wear come from.

How we run a flooring installation job in Roswell

1

Pull back a corner and see what is really there

Before anything is ordered we lift a corner of the existing carpet or flooring to see the subfloor, the height against the next room, and whether the house is on a slab or a crawlspace. What is under the floor, not the sample in the showroom, decides what can go down and what prep it needs.
2

Test for moisture and check the subfloor

Slabs and crawlspace subfloors are checked for moisture before any wood or vinyl is committed, because flooring laid over a wet base fails no matter how well it is installed. We also check the subfloor for flatness and for loose, soft or squeaking spots, and note the height difference into every adjoining room.
3

Fix and flatten the subfloor

High and low spots are ground down or filled with leveling compound, loose panels are refastened to the joists, and soft or water-damaged decking is cut out and replaced. On a crawlspace house a ground vapor barrier is part of keeping the new floor dry. This step is skipped on cheap jobs and is the reason they fail.
4

Acclimate the material

Wood and some vinyl are brought into the actual rooms and left to reach the home humidity before a board goes down. In a Georgia summer that matters: material installed straight off the truck swells or shrinks to the room later and opens gaps or buckles. We measure it rather than guess.
5

Lay the floor and handle transitions

The floor goes down by the method the material calls for — nail, glue, or floating click — with the right underlayment under it. Thresholds and transitions into tile, other rooms and stair nosings are cut so there is no trip edge, and doors are undercut so they still swing.
6

Trim, clean and walk it

Shoe molding or base is set to cover the expansion gap, seams and transitions are checked, and the floor is cleaned. We walk it with you in good light, looking for lifted edges, hollow spots and anything that catches, and work a punch list before it is closed out.

What moves the price

We will not quote Roswell blind over the phone — these are the things we look at on site that decide the number.

What is under the existing floor. Carpet over sound plywood pulls up easily; tile or glued vinyl, or a bad subfloor found underneath, adds removal and prep that a showroom quote never includes.
Material class. Laminate and vinyl plank sit at the low end, engineered hardwood and tile in the middle, and solid site-finished hardwood or natural stone at the top.
Subfloor repair and leveling. Grinding high spots, filling low ones, replacing soft decking, or adding a crawlspace vapor barrier is priced once the old floor is up.
Slab versus crawlspace. A slab limits solid hardwood and may need moisture control; a crawlspace can need subfloor and vapor work before new flooring goes down.
Square footage, and how cut-up the space is. Closets, angles, stairs and lots of doorways slow a job and add transitions and waste.
Stairs, patterns and transitions. Stair treads, diagonal or herringbone tile, and tying several finishes together at thresholds all add labor over a plain straight-lay field.

See typical flooring installation price ranges →

From a flooring installation customer

“The entire inside of my home was gutted and remodeled. … When the home would give us unexpected surprises, Dan would calm me down and give me several options. … The workmanship is impeccable!!”

Tonya W. Johnson
Whole-interior remodel, exterior trim
July 2026

All 44 reviews →

Want a real number for your Roswell flooring installation job?

The only way to price it honestly is to see it. We come out, walk the job and put it in writing — free, and with no obligation to book.

Call and we answer 24/7. Forms sent during the day get a call back the same day.

Call (470) 419-0922 Get a free estimate

Flooring Installation in Roswell — questions we get asked

What is the most important part of a flooring job?: The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.
Should I replace my old hardwood or refinish it?: If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.
Can I put hardwood on a concrete slab?: Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.
Which floor holds up best in Georgia humidity?: Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.
How long does new flooring take?: A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Planning flooring installation? Start here

Everything about flooring installation →

More in Roswell

Fulton County housing, neighborhoods and what we do there.

Painting & remodeling in Roswell →

Other work in Roswell

Flooring Installation nearby

Prefer to talk it through? Dan picks up.