What is the most important part of a flooring job?

The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.

Should I replace my old hardwood or refinish it?

If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.

Can I put hardwood on a concrete slab?

Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.

Which floor holds up best in Georgia humidity?

Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.

How long does new flooring take?

A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Flooring Installation in Johns Creek, GA

Before you replace the hardwood in a Johns Creek home, it is worth finding out whether it can be refinished. The solid three-quarter-inch oak in many Country Club of the South houses usually can, and a modern color on the main level with upstairs carpet replaced is a common project. We measure the wear layer first, check what sits under stair carpet, and match new boards where floors meet. Describe your floors below.

Get a free estimate (470) 419-0922

Fulton County · Johns Creek, GA

Flooring Installation for Johns Creek homes

Johns Creek splits into three rough eras. Rivermont, laid out around a golf course that opened in 1973, holds the oldest subdivision housing, with homes from the mid-1970s and early 80s whose original wiring, windows and wood siding are near the end of their life. The gated golf communities came next: St. Ives, on nearly a mile of Chattahoochee frontage, went up mostly in the late 80s and early 90s, and Country Club of the South followed through the 90s. Those are large estate homes, often brick or stone with stucco sections, tall foyers, two-story family rooms and full basements. Swim-and-tennis neighborhoods such as Seven Oaks, Ammersee Lakes and River Glen are more modest, mostly brick-front houses with lap siding on the sides and back. For painting, that means a lot of tall interior walls and stairwells, plus stucco and trim that need careful repair before a coat goes on. For remodeling, it means second-generation kitchens and baths, and basement finishing in houses that are big to begin with.

Areas we work in Johns Creek

St. Ives
Country Club of the South
Rivermont
Seven Oaks
Ammersee Lakes
River Glen

Near Newtown Park, Autrey Mill Nature Preserve and Heritage Center, Rogers Bridge Park and across the rest of Johns Creek.

Long kitchen with cherry cabinets, stainless appliances and freshly refinished oak floors — Photos from recent WS Painting & Remodeling jobs across the metro.

Living room with glossy refinished oak floors, a white marble fireplace and white columns — Photos from recent WS Painting & Remodeling jobs across the metro.

Flooring Installation on Johns Creek houses

Johns Creek homes from the late 80s and 90s often have site-finished hardwood on the main floor, carpet upstairs and on the stairs, and tile in kitchens and baths. The oak in the Country Club of the South houses is frequently solid three-quarter-inch flooring that can be sanded and refinished rather than replaced, which is often the better choice. Where owners want a new look, the job is usually refinishing the main level in a modern color and replacing upstairs carpet with hardwood or plank. Curved and open staircases make stair treads the most detailed part of many jobs. Rivermont's older homes may have parquet or worn original oak.

What usually gets missed

Before replacing hardwood, find out if it can be refinished. Solid oak can usually be sanded several times, but some floors from this era were already sanded down thin, or are engineered with a thin wear layer. We pull a floor vent or threshold to look at the board edge and measure what is left. When carpet comes off the stairs, the treads underneath are often builder-grade pine that was never meant to be seen.

On a Johns Creek job we check

Pull a vent or threshold to measure the remaining wear layer
Check what is under stair carpet before promising exposed treads
Match new boards to existing oak where floors meet

5.0 from 44 Google reviews. A supervisor runs every job on site.

(470) 419-0922

What the job actually involves

A floor is only as good as what it sits on. Most of a flooring job is the part you never see — checking the subfloor for flatness, moisture and movement, and fixing it — because that is what decides whether the finished floor stays flat, quiet and tight instead of cupping, gapping or squeaking in a year or two.

We install laminate, luxury vinyl plank, engineered and solid hardwood, and tile, matched to the room: vinyl or tile over slabs, basements and wet areas, hardwood in conditioned living space, with the underlayment and transitions the material calls for. We do not pair a good floor with the thinnest underlayment to shave the quote, because that is where noise and early wear come from.

How we run a flooring installation job in Johns Creek

1

Pull back a corner and see what is really there

Before anything is ordered we lift a corner of the existing carpet or flooring to see the subfloor, the height against the next room, and whether the house is on a slab or a crawlspace. What is under the floor, not the sample in the showroom, decides what can go down and what prep it needs.
2

Test for moisture and check the subfloor

Slabs and crawlspace subfloors are checked for moisture before any wood or vinyl is committed, because flooring laid over a wet base fails no matter how well it is installed. We also check the subfloor for flatness and for loose, soft or squeaking spots, and note the height difference into every adjoining room.
3

Fix and flatten the subfloor

High and low spots are ground down or filled with leveling compound, loose panels are refastened to the joists, and soft or water-damaged decking is cut out and replaced. On a crawlspace house a ground vapor barrier is part of keeping the new floor dry. This step is skipped on cheap jobs and is the reason they fail.
4

Acclimate the material

Wood and some vinyl are brought into the actual rooms and left to reach the home humidity before a board goes down. In a Georgia summer that matters: material installed straight off the truck swells or shrinks to the room later and opens gaps or buckles. We measure it rather than guess.
5

Lay the floor and handle transitions

The floor goes down by the method the material calls for — nail, glue, or floating click — with the right underlayment under it. Thresholds and transitions into tile, other rooms and stair nosings are cut so there is no trip edge, and doors are undercut so they still swing.
6

Trim, clean and walk it

Shoe molding or base is set to cover the expansion gap, seams and transitions are checked, and the floor is cleaned. We walk it with you in good light, looking for lifted edges, hollow spots and anything that catches, and work a punch list before it is closed out.

What moves the price

We will not quote Johns Creek blind over the phone — these are the things we look at on site that decide the number.

What is under the existing floor. Carpet over sound plywood pulls up easily; tile or glued vinyl, or a bad subfloor found underneath, adds removal and prep that a showroom quote never includes.
Material class. Laminate and vinyl plank sit at the low end, engineered hardwood and tile in the middle, and solid site-finished hardwood or natural stone at the top.
Subfloor repair and leveling. Grinding high spots, filling low ones, replacing soft decking, or adding a crawlspace vapor barrier is priced once the old floor is up.
Slab versus crawlspace. A slab limits solid hardwood and may need moisture control; a crawlspace can need subfloor and vapor work before new flooring goes down.
Square footage, and how cut-up the space is. Closets, angles, stairs and lots of doorways slow a job and add transitions and waste.
Stairs, patterns and transitions. Stair treads, diagonal or herringbone tile, and tying several finishes together at thresholds all add labor over a plain straight-lay field.

See typical flooring installation price ranges →

From a flooring installation customer

“As an interior designer, my focus is quality of work for my clients. … I especially appreciate suggestions for a course correction on my plan that resulted not only in cost savings but in a much more pleasing and functional result.”

De Smith
Interior design partnership
June 2026

All 44 reviews →

Want a real number for your Johns Creek flooring installation job?

The only way to price it honestly is to see it. We come out, walk the job and put it in writing — free, and with no obligation to book.

Call and we answer 24/7. Forms sent during the day get a call back the same day.

Call (470) 419-0922 Get a free estimate

Flooring Installation in Johns Creek — questions we get asked

What is the most important part of a flooring job?: The subfloor. A floor fails from underneath — a lump telegraphs through vinyl, a low spot leaves a hollow that cracks tile grout, and a wet slab buckles wood. We spend real time flattening, drying and securing what is under the floor, because the finish only lasts if the base is right.
Should I replace my old hardwood or refinish it?: If the existing wood is solid and thick enough to sand, refinishing almost always costs less and lasts longer than covering it with new flooring. We check the boards before you spend money replacing something that only needs sanding and a new finish. Covering good hardwood with vinyl is usually the wrong call.
Can I put hardwood on a concrete slab?: Engineered hardwood can go over a slab once it passes a moisture test, because its layered construction handles the moisture concrete gives off. Solid hardwood cannot be fastened to concrete directly; it needs a wood subfloor or sleepers built over the slab first, which raises the floor and adds cost. On a slab, engineered or vinyl is usually the better call.
Which floor holds up best in Georgia humidity?: Vinyl plank and tile do not care about humidity and are the safe choice over slabs, in basements and in wet areas. Engineered hardwood is stable enough for most of the house. Solid hardwood is fine in conditioned rooms over a wood subfloor but moves the most with the seasons, so it needs the acclimation and gaps done right.
How long does new flooring take?: A single room is often a day or two. A main level is usually several days, more if the old floor fights coming up, the subfloor needs repair, or wood has to acclimate first. Tile adds time for mortar and grout to cure. We give you a schedule after we see what is under the existing floor.

Planning flooring installation? Start here

Everything about flooring installation →

More in Johns Creek

Fulton County housing, neighborhoods and what we do there.

Painting & remodeling in Johns Creek →

Other work in Johns Creek

Flooring Installation nearby

Prefer to talk it through? Dan picks up.